Dengue IgG/IgM Rapid Test: A Practical Procedure Guide for Clinical Users

· By Lisa Zhang, Export Sales Manager · QL Biotek Export Team

Why Dengue Rapid Testing Matters in Practice

Dengue virus is transmitted by infected Aedes mosquitoes and exists as four serotypes: DENV-1, DENV-2, DENV-3 and DENV-4. Infection with one serotype does not protect against the others, which is why repeat infections and severe outcomes remain a recurring clinical concern. Cases range from mild febrile illness to severe dengue with hemorrhagic or shock complications.

For clinics, laboratories and screening programs in endemic regions, the practical question is how to obtain a reliable immunological result quickly, at the point of care, without laboratory instrumentation. The Dengue IgG/IgM Rapid Test Device from QL Biotek is designed for the qualitative detection of dengue antibodies in whole blood, serum or plasma. This guide explains how to run the assay correctly and how to read it with confidence.

What Is Inside the Kit

Each kit contains four functional elements:

  • Individually packed test devices — each device holds a membrane strip with colored conjugates and reactive reagents pre-dispensed at fixed regions for IgM and IgG detection.
  • Disposable pipettes — for transferring a controlled specimen volume to the sample well.
  • Buffer solution — a phosphate-buffered saline with preservatives that drives sample migration along the strip.
  • Package insert — the full procedure and interpretation instructions that should always be followed alongside this article.

Reading IgM and IgG in Context

The device reports two antibody classes, and the distinction matters clinically:

  • IgM is the first antibody produced after dengue infection. It typically appears within 3 to 5 days after symptom onset and points toward an acute infection.
  • IgG develops later and persists long-term. Its presence indicates previous exposure, and early detection alongside symptoms may suggest a secondary infection.

Because the assay is qualitative, results should be interpreted together with the patient's clinical picture and symptom history rather than in isolation.

Storage and Sample Preparation

Store unopened test kits between 2°C and 30°C, protected from direct sunlight, moisture and excessive heat. Damaged storage is one of the most common causes of faint or absent lines, so verify storage conditions before dispensing kits to field sites.

Suitable specimens are whole blood, serum and plasma. If a sample has been refrigerated or frozen, bring it to room temperature and mix it thoroughly before testing. Plasma is obtained by anticoagulant collection and centrifugation; serum is obtained by allowing blood to clot and then centrifuging. Both should be free of clots, debris, hemolysis and lipemia.

Procedure for Whole Blood Samples

  1. Collect a blood sample using a sterile lancet or needle and confirm it is free of clots or debris. Mix thoroughly.
  2. Place the test device on a clean, flat surface.
  3. Fill the dropper and add one drop (approximately 10µL) of whole blood to the sample well.
  4. Immediately add two drops (approximately 80µL) of buffer to the same well.
  5. Start a timer. Read the result at 15 minutes.

Procedure for Plasma and Serum Samples

  1. Place the test device on a clean, flat surface.
  2. Fill the dropper with plasma or serum, ensuring the sample does not exceed the specimen line on the pipette.
  3. Add one drop (approximately 5µL) of sample to the sample well.
  4. Immediately add two drops (approximately 80µL) of buffer.
  5. Read the result at 15 minutes.

Important: never read the strip after 30 minutes. Late lines that appear outside the reading window are not reliable and should be disregarded.

Interpreting the Result

The strip shows two test regions — IgM and IgG — plus one control region. Read them as follows:

Pattern observedInterpretation
Control line plus IgM linePositive for IgM: acute infection likely
Control line plus IgG linePositive for IgG: past exposure or possible secondary infection
Control line plus both IgM and IgG linesPositive: antibodies to dengue present
Control line onlyNegative: no dengue antibodies detected
No control lineInvalid — repeat with a new device

The control line acts as an internal procedural control. It confirms that the device is functioning and that sufficient sample and buffer were applied, producing successful membrane wicking and reagent activation. A result without a control line has not passed procedural validation, regardless of what appears in the test regions.

Common Errors and Troubleshooting

Most invalid or ambiguous results trace back to a small set of correctable mistakes:

  • Expired or poorly stored kits — check expiry dates and confirm the 2°C–30°C storage range before use.
  • Unmixed specimens — re-mix the sample thoroughly before filling the dropper.
  • Air bubbles during sample application — dispense carefully to deliver the full drop volume.
  • Incorrect dosing — verify the specimen line on the pipette and use exactly the specified number of buffer drops.
  • Reading outside the time frame — enforce the 15-minute reading point and the 30-minute maximum.

If the control line does not appear, re-check storage and preparation, confirm sample and buffer volumes, and repeat the test with a new device.

FAQ

Which sample types can be used with the Dengue IgG/IgM Rapid Test Device?

The device accepts whole blood, serum and plasma. Whole blood requires 1 drop of approximately 10µL, while serum or plasma requires 1 drop of approximately 5µL. In all cases, follow with 2 drops (approximately 80µL) of buffer. Samples previously refrigerated or frozen must be brought to room temperature and mixed before testing.

When should the result be read, and what happens if I read it later?

Read the test at 15 minutes. Results must not be interpreted after 30 minutes, because lines that develop outside the validated window may be misleading. Set a timer as soon as buffer is added to keep the reading consistent across operators and sites.

What does a missing control line mean?

A missing control line means the test is invalid. It indicates that the sample migrated through the membrane incorrectly or that the device did not activate as expected. Repeat the procedure with a new test device, and first verify kit storage conditions, specimen quality and the accuracy of sample and buffer volumes.

Talk to a real person. Questions about this topic, IFUs, samples or pricing? Contact Lisa Zhang (Export Sales Manager) — official quotation within 24 hours.

WhatsApp +86 153 0654 9980 Email Enquiry